Logo
Logo
Logo

Underfloor cooling can make indoor spaces more comfortable in summer, but it requires one essential precaution: the floor must not become too cold for the amount of moisture in the air. If surface temperature and humidity are not managed together, condensation can form, potentially affecting both occupants' comfort and floor finishes.

Understanding how to prevent it means distinguishing between two functions of the system: the radiant floor absorbs heat from the rooms, while air treatment removes water vapour. Controls connect these functions, adapting operation to the actual conditions in the home.

In brief

Condensation in underfloor cooling forms when the surface temperature reaches or falls below the dew point of the indoor air. To prevent it, the radiant surface must remain above this threshold with an appropriate safety margin, while a correctly sized dehumidification system reduces humidity. Sensors and controls coordinate water temperature, indoor conditions and the operation of the components.

Why does condensation form with underfloor cooling?

Condensation occurs when a cold surface comes into contact with sufficiently humid air. The key reference is the dew point: the temperature at which, under given conditions, water vapour in the air begins to condense. Knowing the room temperature alone is therefore not enough: the moisture content of the air also matters.

An example makes this clearer. In a room at 26 °C and 65% relative humidity, the dew point is approximately 19 °C. If part of the floor reached 18 °C, condensation could form on its surface. This is an illustrative example of moist-air physics, not a design temperature to apply to every system: the value changes as indoor temperature and humidity change.

This explains why controls cannot simply maintain a fixed chilled-water temperature. Humidity can rise during the day when windows are opened, people enter a room or household activities take place. A properly designed system must account for these changes and protect radiant surfaces against condensation.

How does underfloor cooling work, and what are its limitations?

A radiant floor provides cooling by circulating temperature-controlled water through circuits installed beneath the floor finish. Cooler than its surroundings, the surface absorbs sensible heat from people and surrounding surfaces, helping create comfortable conditions through broad, even heat exchange.

However, the floor should not be expected to perform a function it does not provide: a radiant system does not directly remove water vapour from the air. In other words, it can handle part of the summer cooling load, but it does not replace dehumidification. Its cooling capacity is also constrained by the minimum permissible surface temperature, the floor construction, humidity and the building's loads.

Radiant cooling must therefore be assessed at the design stage. Orientation, solar gains, insulation, glazed areas, air exchange and floor finishes all influence the result. Where the floor alone cannot meet the cooling load, a dedicated supplementary system may be needed, designed to work consistently with the rest of the installation.

What role does dehumidification play in radiant cooling?

The dehumidifier addresses the part of the problem that the floor cannot solve: moisture in the air. By removing water vapour, it helps lower the dew point and increase the margin between this threshold and the floor surface temperature. It therefore supports comfort while also playing an essential role in protecting the system against condensation.

In EMMETI solutions for radiant cooling with dehumidification, air can be treated by neutral-air units or units that provide supplementary cooling, depending on the chosen configuration. Neutral-air units remove moisture without primarily aiming to lower the supply-air temperature. This distinction matters: cooling air and dehumidifying it are different processes, even when one device can contribute to both.

Correct sizing depends on the amount of moisture to be removed, occupancy, air infiltration, air exchange and the local climate. Ventilation also needs careful assessment: a conventional mechanical ventilation system renews the air, but does not automatically provide active dehumidification. To combine air renewal and humidity control, EMMETI also offers Recupera Dry-300, which brings both functions together in a dedicated solution.

How can temperature and humidity control prevent condensation?

Condensation prevention works when controls consider room temperature, relative humidity and water temperature together. Temperature and humidity determine the dew point, while the control system must prevent the radiant surface from reaching critical conditions. Depending on the design, it can adjust the supply-water temperature, limit cooling and activate dehumidification according to the specified control logic.

Water temperature is not necessarily the same as floor temperature: thermal resistance and response times are involved between the water circuits, screed and floor finish. There is therefore no single supply-water temperature suitable for every home. It must be defined with regard to the system's actual behaviour, the floor finish and an appropriate safety margin above the dew point.

Within an EMMETI system, coordination can be provided by the control solutions specified for the project. In particular, the FEBOS X supervisor, paired with Mirai SMI Leaf and Mirai SMI 4.0 heat pumps, allows indoor comfort parameters to be managed and includes functions that optimise underfloor cooling to prevent condensation. FEBOS X does not replace the dehumidifier: it supports the coordinated operation of the devices included in the installation.

How do the heat pump, radiant floor, dehumidification and FEBOS X work together?

The result depends on cooperation between generation, distribution, air treatment and management. Mirai SMI 4.0 and Mirai SMI Leaf heat pumps can produce chilled water for cooling. The EMMETI Floor system uses the radiant surface to absorb heat from the rooms, while dehumidification removes moisture from the air.

Controls then coordinate these functions. Their role is to keep system operating conditions consistent, preventing cooling demand from driving the floor towards temperatures that are incompatible with the humidity level. The principle is straightforward: the floor mainly handles sensible heat, air treatment handles the latent load, and controls coordinate both requirements.

This is the same integrated design approach explored in our article “Heat pumps and radiant systems: why do they work so well together?”: performance depends on consistent operating conditions for each component, rather than simply combining efficient products.

What precautions are needed when designing and using the system in summer?

Condensation prevention starts before the system is switched on. Actual cooling demand, moisture gains, dehumidification capacity and the response of the radiant system must all be checked. The floor finish also matters: different materials have specific thermal resistance values and installation requirements, which should be assessed with the designer and material manufacturers.

Other parts of the system also need attention: manifolds, valves and pipe sections carrying chilled water can be exposed to condensation if they are not properly protected and insulated against water vapour. Commissioning should therefore include checks of sensors, settings, dehumidifier drains, insulation of chilled-water lines and system behaviour under the most humid summer conditions.

In everyday use, extreme settings should be avoided. Significantly lowering the water temperature to cool rooms more quickly does not solve the problem and can increase condensation risk. It is better to let the controls maintain stable conditions, while paying attention to sudden inflows of warm, humid outdoor air. If wet floors or persistent humidity are noticed, the system must be checked: water on the floor should not be regarded as a normal consequence of radiant cooling.

What approach does EMMETI take to reliable summer comfort?

A summer radiant installation should be assessed as a complete climate control system, rather than simply a floor with cold water flowing through it. The heat pump, dehumidification capacity, radiant distribution and controls must suit the building and how it is used. This integration is the foundation for comfort, reliable operation and condensation prevention.

Before components are selected, the decisive assessment therefore concerns the design: which loads the system must handle, how much moisture it must remove, and how a safe margin above the dew point will be maintained in the different areas of the home.

Frequently asked questions

Does underfloor cooling always cause condensation?

No. Condensation can form when the floor temperature reaches or falls below the dew point of the indoor air. Correct design, with humidity control and temperature regulation, is intended to prevent this condition.

Can underfloor cooling be used without a dehumidifier?

The need for air treatment and its configuration depend on project-specific calculations. However, active humidity control is normally a fundamental component of summer radiant cooling, helping manage the latent load and prevent condensation; the floor alone does not dehumidify.

What should the water temperature be in an underfloor cooling system?

There is no single value suitable for every building. The supply-water temperature must be designed and controlled in relation to the dew point, expected surface temperature, floor finish and cooling load.

Does mechanical ventilation remove summer humidity?

Mechanical ventilation renews the air, but does not guarantee dehumidification on its own. Active reduction of summer humidity requires a dedicated function, such as a dehumidifier or a ventilation unit with integrated dehumidification.

Can FEBOS X prevent condensation?

When paired with compatible EMMETI systems and configured as part of the project, FEBOS X includes functions that optimise underfloor cooling to avoid condensation. Controls must still work alongside properly sized generation, distribution and air treatment.

Sources

ASHRAE Handbook, Radiant Heating and Cooling, condensation control section: https://handbook.ashrae.org/Handbooks/A23/SI/A23_Ch55/a23_ch55_si.aspx

ISO 11855-1:2021, Embedded radiant heating and cooling systems, definitions and comfort criteria: https://www.iso.org/standard/74682.html

EMMETI, EMMETI Floor FAQ, underfloor heating and cooling: https://emmeti.com/en/service-area/faq-frequently-asked-questions/emmeti-floor-underfloor-heating-and-cooling

EMMETI, Dehumidifiers for radiant cooling: https://emmeti.com/en/products/air-conditioning/dehumidifiers-for-radiant-cooling

EMMETI, FEBOS X: https://emmeti.com/en/products/air-conditioning/residential-inverter-air-to-water-heat-pumps/febos-x/febos-x

EMMETI, Recupera Dry-300: https://emmeti.com/en/products/air-conditioning/controlled-mechanical-ventilation/cmv-dual-flow-unit-with-dehumidification-recupera-dry/recupera-dry-300-cmv-unit-with-dehumidification-and-air-treatment